View TFS211-1_1324483.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Filename: tfs 211-1.doc
Version 1.8
03.08.2004
VI TELEFILTER
Measurement condition
Filter specification
TFS 211-1
1/5
Ambient temperature: 23 C Input power level: 10 dBm Terminating impedance: Input: 280 II -3,7 pF Output: 280 II -3,7 pF External coil: 127 nH The filter supports bursted GMSK and EDGE modulation.
Characteristics
Remark: Reference level for the relative attenuation arel of the TFS 211-1 is the filter attenuation at 211 MHz. The filter attenuation at 211 MHz is called insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below also if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
Insertion loss (Reference level) Centre frequency Nominal frequency 3dB Bandwidth Relative attenuation a rel fN ... fN 50 fN 50 kHz ... fN 80 fN 80 kHz ... fN 100 fN fN fN fN 200 400 600 800 kHz kHz kHz kHz ... ... ... ... fN fN fN fN 400 600 800 100
GD fN 50 kHz a e = amin fc fN
typ. value
4,5 211,0 dB MHz
tolerance / limit
max 6,5 dB
211,0 MHz 25 kHz 211,0 MHz
270 kHz kHz kHz kHz kHz kHz MHz 3,4 -71 -71 -
kHz
min max max max min min min min
215 1,5 2 3 3 25 35 40 5 1,0 -
kHz dB dB dB dB dB dB dB s s
Group delay at fN Group delay ripple
s
max max
Out of band intermodulation Input signals at 211,8 and 212,6 MHz at +10 dBm Input signals at 210,2 and 209,4 MHz at +10 dBm Input power level for less than 1 hour over life time fN 800 kHz ... fN 3 MHz fN 3 MHz ... fN 100 MHz Return loss (S11/S22)
fN 100 kHz
dBm dBm max max max max min
15 25 22 25 10
dBm dBm dBm dBm dB
Operating temperature range Storage temperature range Temperature coefficient of frequency Frequency inversion temperature ca. - 0,036 + 20 C ppm/K
- 5 C ... + 80 C - 40 C ... + 85 C
Generated:
Checked / Approved:
Tele Filter GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 211-1.doc
Version 1.8
03.08.2004
VI TELEFILTER
Filter specification
TFS 211-1
2/5
Construction, pin connection and 50
- matching network
S211/1 N07
Date Code
1 2 3 4 5
Output Ground External Coil Ground Ground
6 Input 7 Ground 8 Ground 9 Ground 10 Ground
Date Code: L M N ...
1 10 9 2 3 4
Year + week 1999 2000 2001
5 8 7 6
50 Ohm matching networks
C1 6 1 C2
3 L1
L3 L2
2,4,5,7,8,9,10
L4
6
1
L5
C3
3
L3 C4
2,4,5,7,8,9,10
Tele Filter GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 211-1.doc
Version 1.8
03.08.2004
VI TELEFILTER
Stability Characteristics
Filter specification
TFS 211-1
3/5
After the following tests the filter shall meet the whole specification: 1. Shock: 2. Vibration: 3. Damp heat: (cycle) 4. Resistance to solder heat (reflow): 5. ESD 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 25 C to 55C / 95% r.H. / 10 cycles DIN IEC 68 - 2 - 30 Db max. 2 times reflow process; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; MM:200V;
Packing
Tape & Reel: IEC 286 - 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm
Pull Off Direction
Tape (all dimensions in mm) W : 16,00 0,3 Po : 4,00 0,1 Do : 1,50 +0,1/-0 E : 1,75 0,10 F : 7,50 0,10 G(min) : 0,60 P2 : 2,00 0,1 P1 : 12,00 0,1 D1(min) : 1,50 +0,1/-0 Ao : 7,60 0,10 Bo : 9,60 0,10 Ct : 13,5
Date Code P1 Po P2
t
Do
Ko
Typ
PIN Marker
D1
Ao
W2
Reel (all dimensions in mm) A : 330 W1 : 16,4 W2(max) : 22,4 N(min) : 50 C : 13,0
C A N
W1
The minimum bending radius is 45 mm.
Tele Filter GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 211-1.doc
Version 1.8
03.08.2004
VI TELEFILTER
Filter specification
TFS 211-1
4/5
Air reflow temperature conditions
1st and 2nd air reflow profile
Name: Temperature: Time:
pre-heating periods 150 C - 170 C 60 sec. - 90 sec.
main-heating periods over 200 C 20 sec. - 25 sec.
peak temperature 255 C 5 C
Chip-mount air reflow profile
260 240 220 200 180 temperature / C 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 time / s ec. 140 160 180 200 220 240
Table for temperature vs. time during the air reflow process Tolerance of temperatures: 5 C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / C 23 34 46 60 80 103 121 134 143 150 154 156 158 159 time / sec. 140 150 160 170 180 190 195 200 205 210 215 220 230 240 temperature / C 160 161 164 170 180 205 230 255 230 205 180 165 140 120
Tele Filter GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 211-1.doc
Version 1.8
03.08.2004
VI TELEFILTER
History
Version 1.3 Reason of Changes
Filter specification
TFS 211-1
5/5
Name Dr. Wall
Date 13.07.2000
Change date code to weekly date code. Change filter labelling. Correct tape and reel information. Change stop band attenuation and operating temperature range according to customer's request. Change stop band attenuation in frequency range fN 600 kHz ... fN 800 kHz according to customer requests. Add maximum input power. Add support of bursted GMSK and EDGE modulation. Change power handling, intermodulation and operating temperature range according to customer's request. Change input power level for final test from 0 dBm to 10 dBm ESD limits added
1.4
Dr. Wall
20.12.2000
1.5
Dr. Wall
22.01.2001
1.6
Dr. Wall
15.02.2001
1.7 1.8.
Dr. Wall Strehl
27.02.2001 03.09.2004
Tele Filter GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

▲Up To Search▲

Price & Availability of TFS211-1

	To Download TFS211-1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .